Re: how make san storage emtpy
Please refer the P2000 Command Line Reference (CLI) guide which I have shared earlier and look for section "Settings changed by restore defaults" - this will give you idea about what all will get...
View ArticleMSA2050
Hi Dearsi have 2 * MSA2050 with 18 * 1.2sas10K and 9*400SSD and 9*2TB 7.2K------2*g10dl380 and 1*blade(620c*2 and 420c*1 with 8TB configured alredy with esx5.5)i want them for virtualization...
View Articlesetup MSA2050
Hi Dearsi have 2 * MSA2050 with 18 * 1.2sas10K and 9*400SSD and 9*2TB 7.2K------2*g10dl380 and 1*blade(620c*2 and 420c*1 with 8TB configured alredy with esx5.5)i want them for virtualization...
View ArticleRe: setup MSA2050
Hias you have no performance license and with MSA2050 you can only configure virtual poolsthis means you should configure a pool with the same disk drives. you have 18 drives of 1.2TBso you can create...
View ArticleRe: setup MSA2050
Without a performance tiering license you cannot have SSD in any pool if there is also a spinning disk in any pool. Putting SSD in one pool and non SSD in another will not get you around the license...
View ArticleRe: setup MSA2050
hi thank you for your answer giladzzz you mean i use 18 1.2 in first 2050 and ssd in second one so it should be like this:1- msa(1) -> (9*1.2+1ssdRC)+(9*1.2+1ssdRC) all raid 5--->ramaining...
View ArticleRe: setup MSA2050
HelloThe license for tiering is PN Q0H99A "HPE MSA Advanced Data Services Suite LTU". There is also a support component (cost) that goes along with that license. The part number for support differs...
View ArticleMSA2040 multipath config
Hi,Please your help, we have the following scenario:Redhat 6.9BL460c Gen8 (c7000 chassis with 2 SAN switch, all well interconnected)MSA2040 SANOne presented volume 6TB to this host (only)An the...
View ArticleMSA 2050 Jumbo Frame 'issue'
Hello AllWe have an MSA 2050 connected through it's own VLAN, via a HPE FF5700 to 5 HPE Gen10 ESX 6.7 servers.We have created the datastores in VM on the SAN.I have read the best practice guide for the...
View ArticleChange the port connector FC to iSCSi
Hi, I was change the connector FC to iSCSI.The command "show ports"Ports - A1Media - FC(-)Target ID -207000c0ff298f73Status - DisconnectedSpeed - AutoHealth - FaultReason - The installed SFP does not...
View ArticleRe: Change the port connector FC to iSCSi
You know, that iSCSI need different SPF's than FC?If you have already changed the SPF's try this:Use the set host-port-mode CLI command to set the host interface protocol for MSA 2040 SAN host ports...
View ArticleRe: Change the port connector FC to iSCSi
The command "set host-port-mode" was not recognizedI have a MSA 1040, this command only works with 2040
View ArticleRe: Change the port connector FC to iSCSi
It's not possible to change Host port mode from FC to iSCSI in case of MSA1040 (design limitation) and that's why you are unable to do the same.This is possible in MSA2040 Hope this...
View ArticleClik here to view.
MSA 2050 storage question/issue
Hi,Just got the responsibility for our MSA 2050 san.I have some questions about the storrage.B pool is right now "overcommited", it did have some TB free last day.in Vcenter, i can see there should be...
View ArticleRe: MSA 2050 storage question/issue
Overcommitted means you have assigned out more, in volume space, than you actually have in physical space in the SAN. This space is thin provisioned so you may not have actually used it yet but you...
View ArticleRe: MSA 2050 storage question/issue
Hi, Thanks for your answer.with the MSA standpoint, you mean the volumes?i recently tried to migrate a our exchange server from one datastore to another datastore, in the same Pool. and id did fail....
View ArticleRe: MSA 2050 storage question/issue
My understanding in a storage vmotion is that VMWare first copies the entire VM, verifies it's 100% good, and then deletes the source. So, it is possible you will need 2x the space to do the move (at...
View ArticleClik here to view.
Re: MSA 2050 storage question/issue
Acording to this, i really dont have much space.Im trying to see what really takes the space. but i cant find a soulution on that.
View Article