Please help choose the right SAN solution in Chicago, IL
Greetings:We are looking for a SAN to be the backup repository on premise.-Capacity 15TB to start and ability to grow. -Put an identical unit in a colocated offsite location. -SAN's should...
View ArticleClik here to view.
Re: Please help choose the right SAN solution in Chicago, IL
Hi,I recommend you go to this web page and click on either "Contact Us" or "Chat" who can then help you: https://www.hpe.com/us/en/storage/networking.htmlMargaret NHPE Community ManagerAny personal...
View ArticleSerial Number on MSAP2000 G3
I need to get the serial number off the unit, however it appears that its on top of the chassis? Is there any other way to obtain the serial? Seems very inconvinient to have to unrack the unit to get...
View ArticleClik here to view.
Re: Serial Number on MSAP2000 G3
If the system is running, you can ssh/telnet to and runshow enclosure-statusthis will show the chassis serial within the first lines.IIRC the serial is on a sticker near the slots of the power supplies...
View ArticleDAC Copper Cable J9283B or DAC Copper Cable 487655-B21 What to choose?
Hi,We purshaced recently a HP MSA 1040 with two controllers iSCSI 10GbE.We want to attach it to a CISCO switch SG350XG-2F10 with a direct cable, in the documentation there are two options for us, but...
View ArticleMSA1040 Radius or Active Directory
Hi,I have a MSA2312i and a MSA1040 where I want to authenticate logins via Radius or Active Directory but I'can't find anyting in the User Guides.Can you please help!RegardsMarcus
View ArticleHP 2040 SAN Storage
Hi,I have an HP 2040 Storage with me connected to Cisco nexus 2k. Our network team is facing challenge in pinging the management port on the storage.They confirm that the speed on the mgmt port is set...
View ArticleRe: HP 2040 SAN Storage
AFAIR the setting is always AUTO, you cannot change:set network-parameters[controller a|b][dhcp][gateway gateway][ip address][ipv 4|6][netmask netmask][ping-broadcast enabled|disabled|on|off] to check:...
View ArticleRe: HP 2040 SAN Storage
Thanks for the reply Torsten.Please note that once the ip is set on the management port , it is not pinging from the switch but it does ping when I connect my laptop directly to the mgmt port.The...
View ArticleRe: HP 2040 SAN Storage
These commands are not documented in the CLI guide, but however, you may executeset network-parameters auto-negotiation on link-speed 100mbpson the controller you want to change.Check with "show"...
View ArticleRe: HP P2000 Automated Buildout of Storage
Same issue here.Do you already have a solution?I'm trying using it to scrub my vdisk at a specific time and date.Regards,Stephan
View ArticleMSA2040 Direct Attached FC - Move 1 Server to other room using single mode fiber
Dear,We are currently running a small dual Server<>SAN VMware system in a single rack.These are the components: SAN: 1x K2R80A HP MSA 2040 ES SAN DC SFF StorageServer: 2x 752689-B21...
View ArticleMSA 2040 MPIO (along with recent change from linear to virtual disk groups)
So previously, running vSphere 6, configured with MPIO (each host has 2 controllers to SAN, 1 to controller a, and 1 to controller b), using round robin (of course both links are active, but only 1...
View ArticleStorageworks MSA 2312fc dead
Dear community,I wanted to replace my server rack and shutdown all components, also my MSA 2312fc. After shutdown I detach power and replace my rack.Unfortunately all hardware starts without problems...
View ArticleClik here to view.
HP Storageworks G3 P2000 Firmware? Issue
Hello Everyone.We recently had a power failure and afterwards when our p2000 came back online, one of the controllers seems to have failed. The MAC and IP both show as all 0 and it will not take any...
View ArticleRe: HP Storageworks G3 P2000 Firmware? Issue
Similar problem herehttp://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c03178496Reinstall the bundle on this controller (disable PFU, use SMU to update).
View ArticleRe: HP Storageworks G3 P2000 Firmware? Issue
Hi, thanks for your response Torsten.I extracted the bin from the firmware upgrade tool and ran it on the SMU with PFU disabled. It finished with no problems however the Managment controller loader...
View ArticleRe: HP Storageworks G3 P2000 Firmware? Issue
Is this a single enclosure? However, found this:http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c02986398 maybe you need...
View ArticleNot operating one of the two controllers hp MSA p2000 G3
When planning a power failure in the building, we had to turn off the HP P2000 G3 MSA Array Systems (2 controllers and 2 power supply unit). When the LED on the front panel of the figure 8.Behind PUF...
View Article