Re: HP MSA Question
Your best bet is to use the USB Micro CLI port on the back of the system to direct access and find the IPs using the CLI commands. Default username/password: manage/!manageUnfortunately the P2000 is...
View ArticleRe: MSA1060 SAS with two Vmware nodes on Cisco UCS C220 M5SX
Thanks for the additional information. In the past, on other OSes, there have been issues as the SAS protocol typically does not connect to a shared storage device and deep in the 'registry' the HBA...
View ArticleRe: Cannot Access SAN MSA 2040
You mentioned the following:- We try to restore default parameters with restoredefaults and restoreusers and retry, nothing change- All led seems ok, just on the second controller one led is off...
View ArticleRe: Cannot Access SAN MSA 2040
hey , and we dissassembly all part we can, there was some dust but we don't see other visual problem.One thing i forget to precise, we don't really care about our data because we were going to reset...
View ArticleMSA 2040
Dear Community, W are using the HP MSA 2040 SAN Storage. The one of the disks failed. The disk size is 1.8 TB SAS 10 K RPM . The disk Firmware version is HPD2. The MSA SAN Storage system version is...
View ArticleClik here to view.
Re: Cannot Access SAN MSA 2040
So i have try steps, without success... I send you screen and photo (i know fiber not connected, but normally not impact CLI right ?)
View ArticleRe: MSA 2040
Hiall the information you need is here in this sitehttps://h41111.www4.hpe.com/storage/msafirmware.html Also if the drive is the same model usually the MSA does nothave a problem with itRegardsGive a...
View ArticleRe: MSA 2040
Don't forget to check out the FREE MSA HealthCheck it will also guide you to the direct links for the firmware downloads.https://www.hpe.com/storage/msahealthcheck
View ArticleChanging Default IPs on MSA 2050 SAN
I've inherited an MSA 2050. I want to enable SMTP, but they used the default 10.0.0.2/10.0.0.3 (non-routable IPs) for the management console.Am I able to change the IPs to another reserved IP address...
View ArticleQuery: Changing Default IPs on MSA 2050 SAN
System recommended content:1. HPE MSA 2050 User Guide2. HPE MSA 2050 Storage - Supported Configurations Please click on "Thumbs Up/Kudo" icon to give a "Kudo". Thank you for being a HPE valuable...
View ArticleRe: Cannot Access SAN MSA 2040
I apprecaite you letting us know the data is not important. The next steps I am suggesting should only be tried on a system that either has a valid backup or there is no data of value.You do not need...
View ArticleRe: Changing Default IPs on MSA 2050 SAN
Yes, ou can change the IPs on the controllers without affecting data on the system. The following document has steps: HPE MSA 2050 User GuideIf you wish to check your firmware on your system you can...
View ArticleRe: Changing Default IPs on MSA 2050 SAN
Thanks for the assistance Shawn. I appreciate it! I'll schedule the change with the appropriate teams. DR
View ArticleRe: Changing Default IPs on MSA 2050 SAN
Shawn... One last question...If I change the IP on the Management Port A and B from 10.0.0.2 and 10.0.0.3 (respectively) to routeable IP addresses, will I lose access to see the storage?DR
View ArticleRe: Changing Default IPs on MSA 2050 SAN
If you are using SMU, I suggest changing the IP address in the opposite controller and then test that you have access to the other controller's SMU. Then change the opposite controllers IP address. If...
View ArticleRe: Cannot Access SAN MSA 2040
I know on one screenshot login is incorrect, but it's the same than the other (user: manage manage and password: !manage)
View ArticleMSA 2052 Volume Expansion
A client has the need to increse the size of an ISCSI volume connected to a physical server. I added a disk group to Pool A, which is where the volume draws from. It appears that the avail space in...
View ArticleRe: MSA 2052 Volume Expansion
Hello ,Please check if you find this discussion chain (about expanding MSA volume)...
View ArticleMSA 2040: Discovery shows ports that are not mapped
Hi,I'm a total newbie to SAN , but have managed to get it working so far. However, some things don't look right to me.I have attached two hosts via DAC (two cables each). vm03 to controller A1 and B1,...
View ArticleQuery: MSA 2040: Discovery shows ports that are not mapped
System recommended content:1. HPE MSA 1040, MSA 2040, and MSA 2042 Storage GL225R003 Firmware Release Notes2. HPE MSA 2040 User Guide Please click on "Thumbs Up/Kudo" icon to give a "Kudo". Thank you...
View Article