Procedure to add a new enclosure in HP MSA P2000 G3
Hi Folks, Currently we have a HP MSA P2000 with P2000 G3 controllers and one P2000 6Gb drive enclosures.I need to add an extra enclosure P2000 6Gb drive with 12 disk drives , I found the User Guide at...
View ArticleRe: Procedure to add a new enclosure in HP MSA P2000 G3
You can refer these forums and having some useful...
View ArticleRe: MSA 2052 Auto-Tiering vs ReadCache on both controllers
Good to hear the same.Request you to mark the forum as resolved if there is no more outstanding query from your end on this issue.This will help for everyone who are all following your forum. Hope this...
View ArticleHPE 2050 FC firmware compatibility with Solaris, Red Hat and Vmware
HiI have MSA 2050 FC with firmware VL270R001. I have checked in HPE SPOCK page for OS compatibility and found out that Solaris 11 only compat with firmware VL270R004. I also have RHEL 6 x64 and Vmware...
View ArticleRe: Procedure to add a new enclosure in HP MSA P2000 G3
Hello,You state you currently have a P2000 controller enclosure and a additional drive enclosure. You are planning to add another enclosure. To address whether you can add the second drive enclosure...
View ArticleMSA 2040 going from VMWare to Hyper-V
I have an MSA2040 that's currently being used in a VMWare environment. We're getting ready to do a refresh of the hardward (going with Dell and Hyper-V this time around) and am hoping to use the...
View ArticleRe: MSA 2040 going from VMWare to Hyper-V
If you want to move your data from ESX to Hyper-V environment then I would suggest to take data backup. Then unpresent all volumes from ESX environment. Delete all volumes, snapshots and then delete...
View ArticleRe: HPE 2050 FC firmware compatibility with Solaris, Red Hat and Vmware
There is no harm in using all together but major drawback will be you won't get support from HPE for unsupported environment and also it will be unpredictable behavior as anything which is not...
View ArticleRe: HPE 2050 FC firmware compatibility with Solaris, Red Hat and Vmware
Hello,When I check SPOCK I see the MSA 2050 FC is supported with Soloris 11 x64 on VL100R004.SPOCK: https://h20272.www2.hpe.com/SPOCK/Content/ExportPDFView.aspx?Id=13526&typeId=1For VL270R001 I see...
View ArticleRe: HPE 2050 FC firmware compatibility with Solaris, Red Hat and Vmware
wrote:Hello,When I check SPOCK I see the MSA 2050 FC is supported with Soloris 11 x64 on VL100R004.SPOCK: https://h20272.www2.hpe.com/SPOCK/Content/ExportPDFView.aspx?Id=13526&typeId=1For...
View Articleproblems with the size of the snapshots in msa 2040/50
Well, I'm having problems with snapshot management in several msa cabins 2042 and 2052, I'm in 10 Tb luns every snapshot 1 Tb consumes me and I fill the storage quickly. I leave a policy of retention...
View ArticleRe: problems with the size of the snapshots in msa 2040/50
Hello,I must confess I am not fully understanding your post. Perhaps if you provide a little more detail we can help you figure this out. Also, please state whether you are using virtual or linear...
View ArticleRe: problems with the size of the snapshots in msa 2040/50
Thank you very much, sorry for not being more specific. My problem is that I have a Lun in virtual mode of 10 Tb and I detect that each snap consumes 10% of the size. when the 5 instantaneous ones are...
View ArticleHP MSA2040 san connected to superdomex enable SNMP
I have a supoerdomex on RH 7.2 connected to MSA2040 , I have logins to the MSA, and I need toenable SNMP for IRS monitoring. Besides checking the SNMP box, do I have to do anything after that.is...
View ArticleRe: HP MSA2040 san connected to superdomex enable SNMP
Regarding SNMP configuration you can check the below link (Page no 10 onwards),https://h20195.www2.hpe.com/V2/getpdf.aspx/4AA4-6892ENW.pdf Regarding IRS alert SNMP configuration on Linux please find...
View ArticleReset Password for HP storage Works P2000/MSA2000
Hello,Please, how can I reset password for HP storage Works P2000/MSA2000?Thanks
View ArticleRe: problems with the size of the snapshots in msa 2040/50
1st of all you haven't mentioned total Pool sizeHow many volumes are part of that PoolHow much % allocated for snapshotHave you checked if "overcommit" option disabled or enabled in the Pool ? Any...
View ArticleRe: problems with the size of the snapshots in msa 2040/50
Good, attached cabin configuration image
View ArticleRe: problems with the size of the snapshots in msa 2040/50
Good to see the picture but I need more details. Can you please provide the below command outputs,show poolsshow disk-groupsshow snapshot-spaceshow snapshots type allshow volumes Hope this...
View ArticleRe: problems with the size of the snapshots in msa 2040/50
Hello,The Pool shows a total space of 13.3TB, 2220GB of reserved space and allocated space of 11.5TB. This is leaving you 1.8TB of free available space. If as you say you are taking 1TB snaps there is...
View Article