Re: P2000 G3 fault tolerant but with down disk(s)
Read the instructions carefully. Not sure at the moment if you need to upgrade in steps.Backup your data!However, I would disable partner firmware update, then update controller A, then B directly from...
View ArticleMSA-P2000 LUN/Volume mapping
Hi,Recently we had problem with P2000, and it was working fine, after power failure we are facing issue with this storageissue :we can create 100GB volume and can map (Default/Explicit) to server and...
View ArticleRecover MSA2000fc
Hello and thanks for reading,We've had a problem with our MSA2000, I deleted all volumes and Vdisks to start from scratch.The problem nos is that when I try to create a new vdisk from the management...
View ArticleP2000 G3 MSA Performance
Hello,I have a Hyper-V 2012 cluster which points at LUNs based on a P2000 G3 for the virtual servers. My users are complaining about speed issues and one thing that has been flagged is latency in the...
View ArticleP2000 recovery problem
Hello,after a controller of a P2000 storage failed, we aquired a new controller which has a slightly newer firmware than remaining controller has. The partner firmware upgrade fails which results in...
View ArticleRe: P2000 recovery problem
Here is the listhttp://h20566.www2.hpe.com/hpsc/swd/public/detail?sp4ts.oid=4208988&swItemId=MTX_474cd8362e0e4ffea414bd8d50&swEnvOid=4064#tab-history Maybe the version you are looking for was...
View ArticleMSA30, change SCSI controller
Hello,Is it possible to change the dual SCSI U320 controller inside the MSA30 with a dual controller that support Windows 2012 R2 64 bits?Thank you.
View ArticleRe: MSA30, change SCSI controller
The MSA30 is really old now, a single modern disk has more capacity than this array.All 3 different I/O modules are parallel SCSI, so you won't find such SCSI controller for any modern server that runs...
View ArticleRe: MSA30, change SCSI controller
What do you suggest to use for storage with SCSI hdd that support Windows 2012 R2 (like the MSA30)?Thank you for your answer.
View ArticleRe: MSA30, change SCSI controller
My server is a Windows 2012 R2 standard with RAID 5 Adaptec 3405 with four SATA hdd 1 Tb. Two CPU XEON 3.3 Ghz (32 cores) with 64 Gb Ram. Mainboard ASUS...don't remember the model but I think it...
View ArticleRe: MSA30, change SCSI controller
i dont get the problem. msa30 is a dumb disk jbod, no os support is needed.
View ArticleRe: MSA30, change SCSI controller
The SCSI controller...you do need a driver or it's not necessary?HP told me by email that the controller only support Windows 2000/2003. There's no support for Windows 2012. I'm a little lost...
View ArticleRe: MSA30, change SCSI controller
you need a driver for the scsi controller inside your server, your adaptec hba. scsi is too old and slow now. you probably need something sas or sata based. sounds like for home use? what does the...
View ArticleRe: MSA30, change SCSI controller
I wanted to use my old SCSI hdd but if it's too complicated because there's no support for Windows 2012 or Linux than I'll dispose of them.What would you suggest that use 1 to 14 hard disks SAS or SATA...
View ArticleClik here to view.
MSA P2000 G3 and Hardware VSS
I have devices:1. HP MSA P2000 G3 FC/iSCSI2. Blade Enclosure c70003. Cisco MDS 9124e SAN switch3. Server BL460c G6 (1 of 2 host of windows file cluster)4. HBA QLogic2562 8Gb FC (fw 3.75.03)Im try...
View ArticleP2000 G3 iSCSI
I have a failed drive that have been replaced.The current status of the drive is "AVAIL"I wanted to add it as a dedicated spare to my VDISK running RAID10If I do this will I loose the data on the VDISK?
View ArticleRe: P2000 G3 iSCSI
The status AVAIL is normal for a new disk. Now select the vdisk and make it a dedicated spare.
View Article