Re: MSA 2052 Raid configuration
.....Can you please start a new forum with your queries or issues because each forum should be with unique issues only.Admin please move this query and start a new forum. Hope this...
View ArticlePerformance not as expected on MSA 2052
Hello AllWe are refreshing the hardware for our main DB and I'm moving it to new DL380 G10 with 4 x 10GBps interfaces connected to four 10GBps ports - two ports on each of the two controllers of the...
View Article2050 filled with 24 SFF 10k SAS drives
Suppose I have a 1050 or 2050 filled with 24 SFF 10k SAS drives.Or a 2050 with 12 15k SAS drives and 12 10k SAS drives, each group configured as separate pools and LUNs.Will end users notice anything...
View ArticleDrive msa
Hello,We have 600Gb hard drive with the 787642-001 drawer connected to a msa 2040.Because of lack of space, we had to plug a hard drive with a drawer 870794 on the MSA bay.We just changed the drawer...
View ArticleRe: Critical Firmware Upgrade Required For Certain MSA SAS Solid State Drive...
Good day MSA community. I cannot stress enough that everyone should check if they have any of these SSD models installed in their MSA array: HPE Model NumberModel DescriptionMO0400JFFCFHPE MSA...
View ArticleRe: Drive msa
Hello,The drive 870794 is a 600GB SAS HDD but has digitally signed firmware and is designed to work in a Smart Carrier (SC) for a server. This drive is not designed to work in an MSA array due to the...
View ArticleRe: New HPE Tool - MSA Health Check
It is also worth mentioning that embedded in the MSA Health Check Tool (www.hpe.com/storage/MSAHealthCheck) are two excellent videos showing how to save your MSA log file. One video is for Storage...
View ArticleHPE P2000 G3 ISCSI
hi,I have an issue with my HP P2000 G3 the device has 4 ISCSi port and 2 controllers, when I try to ping the IP of the controller A or B it's not replaying even when I am directly connected to the...
View ArticleRe: HP P 2000 G3 ISCSI
Hello Mustafa,It sounds as if your controllers are fine but you are instead having a network issue. Since you have console access you might want to try the following.1. Can you ping one controller MC...
View ArticleRe: HP P 2000 G3 ISCSI
hi Shawn,please check the below comments based on your points,1. Can you ping one controller MC IP address from the other controller? no2. Is the gateway address on the controllers correct and...
View ArticleRe: HP P 2000 G3 ISCSI
You can try restarting both management controllers by below command,restart mc bothPlease note there is no impact to production as you are just restarting management controllers and not Storage...
View ArticleRe: 2050 filled with 24 SFF 10k SAS drives
You missed one important factor which is RAIDIn case 24 SFF 10K SAS drives, there could be many possibilities. You need to consider RAID and Power of 2 as well.In 2nd condition little impact will be...
View ArticleRe: Drive msa
Hello Shawn,Thanks for the comment.Is it possible to update the firmware of the disks for better compatibility with the bay?This one is detected on the bay.Regards,
View ArticleRe: Drive msa
Hello,Unfortunately no. The drive is not supported by the MSA controller, so upgrading the drive is not possible.Cheers,ShawnI work for Hewlett Packard Enterprise. The comments in this post are my own...
View ArticleMSA 2050, MSA 2051, SMA 1050 Default passwords
Can someone advise if the default passwords mentioned in the following website applicable for MSA 2050, MSA 2051, SMA 1050?If any changes, can someone share the...
View ArticleRe: MSA 2050, MSA 2051, SMA 1050 Default passwords
it's same.Please refer Page 44 of SMU guide,https://support.hpe.com/hpesc/public/docDisplay?docId=a00017707en_us Hope this helps!RegardsSubhajitI am an HPE employeeIf you feel this was helpful please...
View ArticleHow to clean old used disk on a MSA 2040
Hi allTo replace a wrong disk I used a disk from antohezr MSA 2040 not used.The unused MSA wasn't cleanned before so the disk I pluuged has a old configuration. The old disk-group appearred in...
View ArticleRe: How to clean old used disk on a MSA 2040
You can execute below command to clear the drive metadata,# clear disk-metadata <disk_location>or you can check the GUI option as below,This command clears metadata from leftover disks only. If...
View ArticleRe: How to clean old used disk on a MSA 2040
Hitjs for the reply.I already tried this command and the ouput is "Error: The specified disk is not a leftover disk. (1.6) - Metadata was not cleared for one or more disks" and the "clear meta-data on...
View Article