B-Series SAN Switches SCOM Monitoring
With the support removal of B-Series SAN switches from HP Storage management pack 3.0 onwards.Does anyone know any free solution for SAN Switches to be monitor/integrate with SCOM 2007/2012?Thanks,
View ArticleLeftHand OS
Good morning.I have a problem of licensing Lefthand 11.5 OS on StoreVirtual 4130, i have a feature key but when trying to install it says the key is too long sometimes says could not read feature key...
View ArticleRe: LeftHand OS
HiAre you trying to do a system restore if yes maybee your USB device is to large use asmall size 1GB or lessalso you can input the feature key manually without USB deviceRegards
View ArticleMSA2040 Virtual Storage Pools A&B - explanation needed
Hi all, I would like to ask about how the virtual storage pools work. According to the best practice, you should balance your performance and storage space between both pools - but why?Does it mean...
View ArticleRe: MSA 1040: How to discover WWN initiator
Hi,I have a HP 8/20 SAN Switch connecting server to storage. I don't have access to settings of this switch, I will try this.About driver, I have the last HBA driver version installed.thanks for you...
View ArticleRe: increase or upgrade my storage
Hello, You can always increase the capacity of your storage and Vdisks by adding drive enclosures (P2000 3.5-inch drive enclosure or D2700). Here are the limitations: Capacity Minimum / with maximum...
View ArticleRe: HP MSA SAN issue
Hello, Cannot comment on this unless I have a look at the logs. Share the logs and I will priovid the best possibele solution. Regards,Jawad Ahmed
View ArticleRe: MSA 1040: How to discover WWN initiator
Hello,Hello,Check if you have created the initiator correctly.Creating an initiator. To create an initiatorDetermine the FC or SAS WWN or iSCSI IQN to use for the initiator.In the Hosts topic, select...
View ArticleRe: HP MSA SAN issue
Turns out data was lost and we had to re-initialise the array! very annoying
View ArticleRe: HP MSA SAN issue
Sorry to hear that. I would recommend that you contact HPE support in future.
View ArticleSetting up a DL380G8 and P2000
So I'm looking at setting up a DL380G8 and connecting it to a P2000G3 enclosure. I'm new to doing this with HP equipment, so I have a few questions.1) Do I need an external RAID card in the G8? Or does...
View ArticleRe: HP MSA SAN issue
Assuming the RAID was RAID5 the failure of 2 disks means data is lost ...
View ArticleRe: HP MSA SAN issue
Well, in this scenario we have an option for using “Trust” commandUsing the trust command The trust command enables an offline vdisk to be brought online for emergency data recovery. This command must...
View ArticleRe: Repairing YM-3591AAR power supply (HP P/N 81-00000051)
Came to repair the power supply YM-3591AAR.Serial number SA060Axxxxxxxxxx. Replaced the faulty Resistor R411. For parallel resistors, the 8.2 kω and 56 kω. Now when the switch unit is in the power mode...
View ArticleRe: MSA2040 Virtual Storage Pools A&B - explanation needed
Yes the Pool A is owned by Controller A and Pool B by Controller B.If one Controller fails, the other takes the Pool and handle both Pools.So best is to have 2 Pools.
View ArticleRe: Setting up a DL380G8 and P2000
Hi, You don’t need any extra RAID card. You can connect server directly to your storage as per your plan.Get back to me for any assistance. Regards,Jawad Ahmed
View ArticleConnecting MSA 2040 ES SAN DC
Hey guys I can not connect to MSA 2040could you help me I put the ip address with htpps and without it I tried both 192.168.0.77192.168.0.204but I can not connect to it is it any soulution ?Thanks
View ArticleRe: Connecting MSA 2040 ES SAN DC
I already connect MSA to DHCP server now I have 2 IP address Could I connect with them orI try to connect by laptop to MSA and put the IP range 10.0.0.1 /2but I did not success again
View Article