Re: HPE MSA2050 MPIO Configuration
In a typical round-robin configuration, MPIO will load balance between both ports on the server and across all optimized paths to a Volume, however it will never drive I/O down an un-optimized path...
View ArticleP2000 MSA G3コントローラー交換時のFW同期アルゴリズムについて
G4/G5世代のMSAのSMUリファレンスガイドには保守部品のコントローラー交換を実施した場合、元のコントローラーから交換部品へFWが同期されるとの記載があるが、P2000 MSA G3には同様の記載が見つかりませんでした。G3のMSAも同様のFW同期アルゴリズムが動作するのか確認したい。
View ArticleREPLICATIONS "Master MSA2052" to "slave MSA 2052"
Hi !SituationWe have two SAN MSA 2052 in our datacenter.The first MSA2052 (SAN01) is in production. It's connected on 3 hypervisor ESX through an 10Gb ISCSI câble.The second MSA2052 (SAN02) is setup...
View ArticleAdding new physical disks
I have a HP MSA 2040 SAN which currently has 12 HP 1.2T SFF SAS 12G/s 10k rpm hdd. I am trying to add 4 more drives with the same specs. As the system is hot swappable I remove the blanks and slide in...
View ArticleRe: Adding new physical disks
Please share the drive model number which are already present in the system. Never share serial numbers in public.Also please share the drive model number which are new and you have added to the...
View ArticleRe: REPLICATIONS "Master MSA2052" to "slave MSA 2052"
You can check the below "MSA Remote Snap Software" technical whitepaper,https://h20195.www2.hpe.com/v2/GetPDF.aspx/4AA1-0977ENW.pdf Hope this helps!RegardsSubhajitI am an HPE employeeIf you feel this...
View ArticleRe: Adding new physical disks
Hello,For the MSA, you must use HPE drives with the correct firmware which has been tested and qualified for the MSA array. For example, if adding 1.2TB drives you need to use part number J9F48A. Using...
View ArticleFW synchronization algorithm when replacing P2000 MSA G3 controller
G4/G5世代のMSAのSMUリファレンスガイドには保守部品のコントローラー交換を実施した場合、元のコントローラーから交換部品へFWが同期されるとの記載があるが、P2000 MSA G3には同様の記載が見つかりませんでした。G3のMSAも同様のFW同期アルゴリズムが動作するのか確認したい。Google TranslatedThe SMU reference guide for the G4 / G5...
View ArticleHP MSA 2040 SAN storage system replace new drive.
One of our disks was reported as faulted. When we put a replacement disk in our storage, it didn't end up in a volume/pool where it should have. Instead, it generated its own volume/pool and made some...
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
version number: GL210R004our In total there are 10 pools. Disk number: 6x25 mostly 600GB SAS, but there are 900GB too.Our system is currently working and our tools can use storage. But current storage...
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
Unable to see any screenshot.1st of all there can be max two pools. With physical drives you make Virtual disk groups. This is for Virtual Array.In case of linear array, with physical drives you make...
View ArticleClik here to view.
Re: HP MSA 2040 SAN storage system replace new drive.
Hi SUBHAJIT KHANBARMAN_1 please find attached screenshot. and provide how should i fix this ?
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
As you are dealing with Linear vdisks so try to login by using SMU Version 2 rather than Version 3,https://<management IP address>/v2/index.htmlAlso you can check from CLI and confirm the...
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
it was lready exists and part of production.
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
Then your concern is why drives are not seen when you select the vdisk from SMU like you can see for other Vdisks.It's just reporting issue for which you can login to one of the Controller CLI and...
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
OK, as i wrote the MSA reporrteds fualty disk and after replacment with nwe one it's came as you see no realated disks up.and i think that i need to configure my MSA before adding new disk. I'll try to...
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
Drive replacement is simple process. You can also have a look at below document,https://support.hpe.com/hpesc/public/docDisplay?docLocale=null&docId=emr_na-c03792356There is no need to reconfigure...
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
Hi SUBHAJIT KHANBARMAN_1 sorry for this, but Vdisk named "itkvfde02_2" was appeared after I have inserted new drive. I have informed about this before i start the Restart for th CM Both.so please lets...
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
Hi SUBHAJIT KHANBARMAN_1 ,I have been informed that my colluge replaced the faulty drive with another drive which was installed on another MSA. and now all what I need is how to delete the Vdisk which...
View ArticleRe: HP MSA 2040 SAN storage system replace new drive.
Thanks for your reply.I already asked you before if vdisk itkvfde02_2 not part of this system or part of your production data. So next thing to do is delete this vdisk.Only I doubt that if vdisk...
View Article