Re: P2000 Password Reset
Thanks for the detailed instructions!I have one question left: will this reset all settings (i.e. storage configuration like arrays and accesses) or just the passwords?Thanks in advance!
View ArticleRe: P2000 Password Reset
Hello,Using the command "restoredefaults" will reset all of the configuration settings back to a default setting. This resets all the array IP addresses, mapping, configuration details, alert settings,...
View ArticleRe: P2000 Password Reset
Thank you for the clarification, Shawn, I really appreciate your prompt answer!I think I don't have support on my storage anymore (that I bought used) but I was lucky enough to find the password I set,...
View ArticleHPE MSA 2040 SAN Disk Failure Notification
Hi. Recently there is a disk failure but NMS did not pick it up. Running on version GL210R004. Upgrade to current version is able to address the problem? Thanks.
View ArticleMSA 2052 Storage allocation query
Hi, I'm looking for some advice on best practice on an MSA 2052 and expander.The MSA has 2 x 800GB SSD and 22 x 1.8TB SAS drives.The expansion cage has 12 x 4TB MDL drives.The SAN is SAS-connected to...
View ArticleMSA 2052 (Q1J03A)
Was wondering if the MSA 2052 San DC Controller will connect to a 10gBaseT network Switch. I am finding conflicting information?I am only finding sfp+ to sfp+ transceivers from HP website. But if i do...
View ArticleRe: HPE MSA 2040 SAN Disk Failure Notification
DerrickAng , I understand. Please try MC restart and it should work.However , HPE advices to upgrade to the latest firmware as and when available. We have 7 versions released after : GL210R004Since ,...
View ArticleHow to failover controller manually
Hi there,This may be a silly question. How do you similate a controller failover on an iSCSI MSA 2052? Do I need to pull out a c ontroller card manually while switched on?I'm used to Nimble which has...
View ArticleRe: How to failover controller manually
Hiyou can do a restart to the storage controller from management consoleRegardsGive a KUDO if this helps
View ArticleRe: How to failover controller manually
MSA 2052 doesnt have an option to do a manual failover with both controllers up.You could shut down one of the controllers so that the second controller takes ownership of all volumes and disk...
View ArticleRe: MSA 2052 Storage allocation query
If you want to know about max limits then I would suggest to go through Quick Spec as below, https://h20195.www2.hpe.com/V2/getpdf.aspx/a00008277enw.pdfSnapshots reference volumes, they take up no...
View ArticleRe: MSA 2052 (Q1J03A)
I dont see support for 10GBASET in MSA 2052 quickspecs or options parts list.It supports 10GbE using either DAC cable or SFP modules.Please check pages 21 and 25 of the quickspecs...
View ArticleRe: HPE MSA 2040 SAN Disk Failure Notification
Thank you. By the way, notification alert priotity should not be critical but fall under error for disk failure? Can I check operation will not be very much affected during upgrade when doing it in...
View ArticleRe: HPE MSA 2040 SAN Disk Failure Notification
There is one known issue I remember regarding drive failure but not getting detected as an alert but this issue was fixed in GL220R005"Event 8 Unknown Reason Drive failure does not create 314...
View ArticleRe: HPE MSA 2040 SAN Disk Failure Notification
Hello,There was more than one error message reporting issue fixed between GL200 and GL225. As mentioned previously, you will have to hop the array from GL200 -> GL220 -> GL225. You can perform...
View Article.vhdx can not be opened by 2012 R2 Hyper-V when copied at HPE MSA 2012SA storage
Hello!We have an additional HPE 421 controller plugged into each of our two HPE ProLiant DL380p Gen8 and into our one HPE ProLiant DL360p Gen 8.At the both HPE ProLiant DL380p Gen8 is with those...
View ArticleRe: How to failover controller manually
Can you please help us to understand if the query has been answered or not?This will help for everyone who are all following your forum.If you feel this was helpful please click the KUDOS! thumb below!
View ArticleRe: MSA 2052 Storage allocation query
Thanks for the reply.The use of this is for archive data (MDL drives) and live project data (SSD and SAS).The live project data is changing frequently and this could be the additon and/or removal of...
View ArticleRe: MSA 2052 Storage allocation query
I would suggest you to go with three tier or Automated Tier setup where you will have SSD, SAS and MDL drives. In your case let's say you have 10TB Thin Volume and out of that around 6TB data is there....
View ArticleRe: .vhdx can not be opened by 2012 R2 Hyper-V when copied at HPE MSA 2012SA...
Hello,Please be aware that the MSA2012SA is an End of Support Life product. The array was never tested nor supported Windows 2012 or Windows 2012 R2. Your solution here of using an DL380 Gen8 with a...
View Article